What is the standard rail in Europe?

Railway track gauge ( mm)

If you want to learn more, please visit our website Yongyang.

A standard-gauge railway is a railway with a track gauge of 1,435 mm (4 ft 8+1&#;2 in). The standard gauge is also called Stephenson gauge (after George Stephenson), international gauge, UIC gauge, uniform gauge, normal gauge in Europe,[1][2][3][4][5] and SGR in East Africa. It is the most widely used track gauge around the world, with about 55% of the lines in the world using it.

All high-speed rail lines use standard gauge except those in Russia, Finland, Uzbekistan, and some line sections in Spain.[6] The distance between the inside edges of the rails is defined to be 1,435 mm except in the United States, Canada, and on some heritage British lines, where it is defined in U.S. customary/Imperial units as exactly "four feet eight and one half inches",[7] which is equivalent to 1,435.1 mm.

History

As railways developed and expanded, one of the key issues was the track gauge (the distance, or width, between the inner sides of the rails) to be used. Different railways used different gauges, and where rails of different gauge met &#; a "gauge break" &#; loads had to be unloaded from one set of rail cars and reloaded onto another, a time-consuming and expensive process. The result was the adoption throughout a large part of the world of a "standard gauge" of 1,435 mm (4 ft 8+1&#;2 in), allowing interconnectivity and interoperability.

Origins

A popular legend that has circulated since at least [8] traces the origin of the 1,435 mm (4 ft 8+1&#;2 in) gauge even further back than the coalfields of northern England, pointing to the evidence of rutted roads marked by chariot wheels dating from the Roman Empire.[a][9] Snopes categorised this legend as "false", but commented that it "is perhaps more fairly labeled as 'Partly true, but for trivial and unremarkable reasons.'"[10] The historical tendency to place the wheels of horse-drawn vehicles around 5 ft (1,524 mm) apart probably derives from the width needed to fit a carthorse in between the shafts.[10] Research, however, has been undertaken to support the hypothesis that "the origin of the standard gauge of the railway might result from an interval of wheel ruts of prehistoric ancient carriages".[11][better source needed]

In addition, while road-travelling vehicles are typically measured from the outermost portions of the wheel rims, it became apparent that for vehicles travelling on rails, having main wheel flanges that fit inside the rails is better, thus the minimum distance between the wheels (and, by extension, the inside faces of the rail heads) was the important one.

A standard gauge for horse railways never existed, but rough groupings were used; in the north of England none was less than 4 ft (1,219 mm). Wylam colliery's system, built before , was 5 ft (1,524 mm), as was John Blenkinsop's Middleton Railway; the old 4 ft (1,219 mm) plateway was relaid to 5 ft (1,524 mm) so that Blenkinsop's engine could be used. Others were 4 ft 4 in (1,321 mm) (in Beamish) or 4 ft 7+1&#;2 in (1,410 mm) (in Bigges Main (in Wallsend), Kenton, and Coxlodge).[13]

English railway pioneer George Stephenson spent much of his early engineering career working for the coal mines of County Durham. He favoured 4 ft 8 in (1,422 mm) for wagonways in Northumberland and Durham, and used it on his Killingworth line. The Hetton and Springwell wagonways also used this gauge.

Stephenson's Stockton and Darlington railway (S&DR) was built primarily to transport coal from mines near Shildon to the port at Stockton-on-Tees. Opening in , the initial gauge of 4 ft 8 in (1,422 mm) was set to accommodate the existing gauge of hundreds of horse-drawn chaldron wagons[14] that were already in use on the wagonways in the mines. The railway used this gauge for 15 years before a change was made, debuting around , to the 1,435 mm (4 ft 8+1&#;2 in) gauge.[page needed] The historic Mount Washington Cog Railway, the world's first mountain-climbing rack railway, is still in operation in the 21st century, and has used the earlier 4 ft 8 in (1,422 mm) gauge since its inauguration in .

George Stephenson introduced the 1,435 mm (4 ft 8+1&#;2 in) gauge (including a belated extra 1&#;2 in (13 mm) of free movement to reduce binding on curves ) for the Liverpool and Manchester Railway, authorised in and opened 30 September . The extra half inch was not regarded at first as very significant, and some early trains ran on both gauges daily without compromising safety.[17]

The success of this project led to Stephenson and his son Robert being employed to engineer several other larger railway projects. Thus the 4 ft 8+1&#;2 in (1,435 mm) gauge became widespread and dominant in Britain. Robert was reported to have said that if he had had a second chance to choose a gauge, he would have chosen one wider than 4 ft 8+1&#;2 in (1,435 mm).[18][19] "I would take a few inches more, but a very few".[20]

During the "gauge war" with the Great Western Railway, standard gauge was called "narrow gauge", in contrast to the Great Western's 7 ft 1&#;4 in (2,140 mm) broad gauge. The modern use of the term "narrow gauge" for gauges less than standard did not arise for many years, until the first such locomotive-hauled passenger railway, the Ffestiniog Railway, was built.[citation needed]

Adoption

In , in the United Kingdom of Great Britain and Ireland, a Royal Commission on Railway Gauges reported in favour of a standard gauge. The subsequent Gauge Act ruled that new passenger-carrying railways in Great Britain should be built to a standard gauge of 4 ft 8+1&#;2 in (1,435 mm), and those in Ireland to a new standard gauge of 5 ft 3 in (1,600 mm). In Great Britain, Stephenson's gauge was chosen on the grounds that existing lines of this gauge were eight times longer than those of the rival 7 ft or 2,134 mm (later 7 ft 1&#;4 in or 2,140 mm) gauge adopted principally by the Great Western Railway. It allowed the broad-gauge companies in Great Britain to continue with their tracks and expand their networks within the "Limits of Deviation" and the exceptions defined in the Act.

After an intervening period of mixed-gauge operation (tracks were laid with three rails), the Great Western Railway finally completed the conversion of its network to standard gauge in . In North East England, some early lines in colliery (coal mining) areas were 4 ft 8 in (1,422 mm), while in Scotland some early lines were 4 ft 6 in (1,372 mm). The British gauges converged starting from as the advantages of equipment interchange became increasingly apparent. By the s, the entire network was converted to standard gauge.

The Royal Commission made no comment about small lines narrower than standard gauge (to be called "narrow gauge"), such as the Ffestiniog Railway. Thus it permitted a future multiplicity of narrow gauges in the UK. It also made no comments about future gauges in British colonies, which allowed various gauges to be adopted across the colonies.

Parts of the United States, mainly in the Northeast, adopted the same gauge, because some early trains were purchased from Britain. The American gauges converged, as the advantages of equipment interchange became increasingly apparent. Notably, all the 5 ft (1,524 mm) broad gauge track in the South was converted to "almost standard" gauge 4 ft 9 in (1,448 mm) over the course of two days beginning on 31 May .[21] See Track gauge in the United States.

In continental Europe, France and Belgium adopted a 1,500 mm (4 ft 11+1&#;16 in) gauge (measured between the midpoints of each rail's profile) for their early railways.[22] The gauge between the interior edges of the rails (the measurement adopted from ) differed slightly between countries, and even between networks within a country (for example, 1,440 mm or 4 ft 8+11&#;16 in to 1,445 mm or 4 ft 8+7&#;8 in in France). The first tracks in Austria and in the Netherlands had other gauges (1,000 mm or 3 ft 3+3&#;8 in in Austria for the Donau Moldau line and 1,945 mm or 6 ft 4+9&#;16 in in the Netherlands for the Hollandsche IJzeren Spoorweg-Maatschappij), but for interoperability reasons (the first rail service between Paris and Berlin began in , first Chaix timetable) Germany adopted standard gauges, as did most other European countries.

The modern method of measuring rail gauge was agreed in the first Berne rail convention of .[23]

Early railways by gauge

Non-standard gauge

Almost standard gauge

Standard gauge

Small deviations from standard gauge

Dual gauge

Initially standard gauge

Several lines were initially built as standard gauge but were later converted to another gauge for cost or for compatibility reasons.[citation needed]

• South Africa became

  1,067 mm

  (

  3 ft 6 in

  )
• Thailand became

  1,000 mm

  (

  3 ft 

  3

  +

  3

  &#;

  8

   in
  )
• Indonesia became

  1,067 mm

  (

  3 ft 6 in

  )
• Ireland became

  1,600 mm

  If you want to learn more, please visit our website European Standard Rails.

  (

  5 ft 3 in

  ) &#; Dublin and Kingstown Railway
• Australia became

  1,600 mm

  (

  5 ft 3 in

  ) &#; Victoria & South Australia &#; partly converted to

  1,435 mm

  (

  4 ft 

  8

  +

  1

  &#;

  2

   in
  )
• India became

  1,676 mm

  (

  5 ft 6 in

  ) &#; initial freight lines
• some private Japanese railways

Modern almost standard gauge railways

Railways

Non-rail use

Several states in the United States had laws requiring road vehicles to have a consistent gauge to allow them to follow ruts in the road. Those gauges were similar to railway standard gauge.[62]

See also

Notes

References

Bibliography

Railway Gauges

Most railways in Europe use the standard gauge of 1,435 mm (4 ft 8+1&#;2 in). Some countries use broad gauge, of which there are three types. Narrow gauges are also in use.

Broad gauge

Narrow gauge

High-speed rail

Apart from Russia and Finland, all high-speed rail in Europe uses standard-gauge (1,435 mm (4 ft 8+1&#;2 in)) tracks.

See also

References

For more information, please visit Russion Standard Rails.